A rear-end crash with a tractor-trailer can become deadly when a car slides under the trailer. The rear impact guard exists to stop that from happening. Too often, however, the guard bends, breaks loose, or misses the car entirely. An underride guard failure can turn a survivable crash into a catastrophic one. This article explains why guards fail, how the federal standard changed, and who may be responsible when a guard does not hold.
What a Rear Impact Guard Is Supposed to Do
Typically, trailers sit high off the road. In a rear-end crash, a passenger car’s hood can slide under the trailer bed. When that happens, the trailer strikes the windshield and the people inside.
For that reason, a rear impact guard hangs below the back of the trailer to block that path. Federal rules generally require trailer guards to sit no more than 22 inches above the ground. Ideally, the guard stops the car before the trailer reaches the passenger compartment, letting the car’s airbags and crumple zones work. Without that protection, even a crash at moderate speed can cause fatal head and neck injuries.
Speak with a Charlotte car accident lawyer and get a free consultation today.
Call (980) 246-2656How the Federal Standard Changed
Historically, federal guard standards date back to the late 1990s. For years, safety researchers warned that those standards did not go far enough. A 2014 National Transportation Safety Board report found guards that bent, detached, or failed when a car struck them off-center.
In 2022, federal regulators upgraded the rear guard standard. The new rule adopted tougher strength and energy-absorption requirements, and compliance became mandatory on . Federal rules had also added rear guards to required annual truck inspections in December 2021.
Importantly, those changes matter in a claim. A trailer built after the compliance date should meet the stronger standard. Older trailers may still be on the road with weaker guards.
Why Underride Guards Fail
Investigators have identified several common ways guards fail. These include:
- Weak attachments: bolts or welds that break, letting the guard tear away
- Offset impacts: a car strikes the guard near one end, where it is weakest
- Trailer flex: the trailer frame bends during the crash and shifts the guard out of position
- Excessive height: the guard sits too high to meet a car’s bumper
- Damage and rust: prior impacts or corrosion weaken the guard over time
- Missing guards: some vehicles have no guard at all or carry a removed guard
Each failure points to a different responsible party. For that reason, examining the guard itself is often the most important step in the case.
Single-Unit Trucks and Older Trailers
Not every large truck follows the same guard rules. Single-unit trucks, such as many box trucks and dump trucks, generally face looser requirements than tractor-trailers. Some may carry guards mounted higher off the ground, and some types qualify for exceptions.
Older trailers raise a different problem. A trailer built before the 2024 compliance date may legally carry a guard designed to the older standard. Even so, a guard that has rusted, bent, or cracked may no longer meet even that standard. Meanwhile, trailers that change hands may lose maintenance records along the way. As a result, identifying the vehicle’s type, build date, and history matters early in any underride case.
Who May Be Responsible for an Underride Guard Failure
In practice, several parties may share responsibility when a guard fails:
- Trailer manufacturer: for a guard that was poorly designed or built
- Guard manufacturer: if a separate company made the guard
- Trucking company: for operating a trailer with a damaged or missing guard
- Maintenance company: for missing or ignoring guard damage during inspections or repairs
- Truck driver: for the conduct that led to the crash, such as a sudden stop or missing lights
Our page on who is liable in a truck accident explains these parties in more detail. In many underride cases, more than one of them contributed to the harm.
Crashworthiness Claims Against Manufacturers
Notably, some underride claims focus less on how the crash started and more on why the injuries were so severe. Georgia recognizes claims that a product made injuries worse than they should have been. In an underride case, that may mean showing a better guard would have prevented the trailer from reaching the passenger compartment.
Not surprisingly, these claims often require engineering experts. They may compare the guard to current standards and to safer designs that already existed. Georgia also sets a ten-year deadline for many product claims against manufacturers, measured from the product’s first sale. That rule can bar claims involving older trailers.
Why the Car’s Driver Is Not Automatically at Fault
At first, insurers often assume the driver who hit the back of a truck caused the crash. Sometimes that driver did share fault. Even so, the trucking company may still bear responsibility for the injuries a failed guard caused.
In addition, trucks must display reflective tape and working lights so drivers can see them. A trailer stopped on the shoulder must use flashers and warning devices. When a truck was hard to see, the car’s driver may carry less of the blame. Dark, rainy nights and dirty or missing reflective tape often make a stopped trailer nearly invisible until the last second. Lighting and conspicuity evidence can change how a jury views the crash.
How Georgia’s Fault Rules Apply
Georgia follows a modified comparative fault rule. Under O.C.G.A. § 51-12-33, a jury can reduce your recovery by your share of fault. If you are 50% or more at fault, you recover nothing.
That rule makes the guard evidence especially important. Proof that a guard failed can shift fault toward the trucking company and the manufacturer. Strong evidence about lighting and visibility can also reduce the share assigned to the car’s driver.
Why the Trailer Itself Is Key Evidence
Underride cases depend on physical evidence. The guard, its mounting hardware, and its certification label tell much of the story. Unfortunately, a carrier may repair or scrap a damaged trailer within days.
Beyond the trailer, other records matter too. Inspection reports, maintenance logs, and the trailer’s build date can show whether the guard met the rules. A preservation letter from a lawyer can stop the carrier from destroying that evidence.
What a Claim Can Cover
Underride crashes often cause head injuries, spinal cord damage, and fatal injuries. A claim may include medical care, rehabilitation, and future treatment. It can also cover lost income and reduced earning ability.
Georgia law also allows recovery for pain and suffering. When a crash takes a life, the family may bring a wrongful death claim, and the estate may recover medical and funeral costs.
Why Hire a Lawyer After an Underride Guard Failure
Ultimately, underride guard cases combine trucking rules, product liability, and engineering. Trucking companies and manufacturers often blame each other or the injured driver. Meanwhile, the most important evidence sits in their hands.
A lawyer can secure the trailer and the guard for expert inspection. Your attorney can also identify every responsible party and every insurance policy. Georgia generally allows two years to file an injury lawsuit, but evidence can vanish much sooner.
For more on underride crashes, see our truck underride accident, rear underride, side underride, and Coweta County underride pages.
Contact a Grantville Personal Injury Attorney for a Free Consultation
If an underride crash injured you or a loved one near Grantville or elsewhere in Coweta County, Shane Smith Law can review your case for free. We will explain your options and the deadlines that apply. You pay no attorney fee unless we recover money for you.
Call 980-246-2656 today to schedule a free consultation.